マイショッピングカート
lonsdor k518isecgdi progskp1000vvdi key toolx300 dpAutosnap AS809-JPBMW Dash Scanner 3 in 1LISHI BMW HU92 Lock PickLISHI 2010 BMW HU-100RYANHUA 2013.07 MB SD Connect Compact 4Key Pro M8MB CARSOFT7.4MultiplexerBMW ICOM 2013.08key m8sk142
トップページ
トップページ - 製品 - 自動車の診断ソフトウェア - ECU Flash Reprogramming for Toyota DVD
«戻る
ECU Flash Reprogramming for Toyota DVD

ECU Flash Reprogramming for Toyota DVD

商品番号 SS54
0 stars, 0 reviews.
在庫あり
現価:3,300 円
数量:
      
9月30日から10月7日まで、商品番号SP326とVIDENTとFoxwellの商品が特価セール。
運送:
無料配送   郵便配送サービス 
配送時間:7-15営業日.詳細»
重量:
0.3KG
返品:
7日以内に返品できますが、ただお客様は運賃を払います。詳細»
ECU Flash Reprogramming for Toyota DVD
IT IS POSSIBLE TO PERMANENTLY DAMAGE THE ECU (ECM/PCM) DURING THE FLASH REPROGRAMMING PROCESS.You must read and understand the following precautionary information before proceeding with reprogramming.

ECU Flash Reprogramming for Toyota DVD


IT IS POSSIBLE TO PERMANENTLY DAMAGE THE ECU (ECM/PCM) DURING THE FLASH REPROGRAMMING PROCESS.
You must read and understand the following precautionary information before proceeding with reprogramming.

You can minimize the risk of damaging an ECU by understanding the following precautions:

1. Battery must be fully charged and in good condition. BATTERY VOLTAGE MUST NOT FALL BELOW 11.4 VOLTS OR RISE ABOVE 16.0 VOLTS DURING THE REPROGRAMMING PROCESS.
2. All electrical accessories must be turned off and electrical loads must not be altered significantly during the reprogramming process (i.e. audio system, air conditioning system, interior lighting, daytime running lights, etc)
3. The engine compartment hood must be open and under hood ambient temperatures must not exceed 158ºF
4. Scantool/J2534 interface cables must be in good condition and connections must be electrically sound prior to beginning reprogramming (see TSB SS004-01, "ECU Flash Reprogramming Error Message" for more detail).
5. Do not disconnect the scantool, J2534 interface or PC during the reprogramming process; FAILURE TO FOLLOW THIS INSTRUCTION WILL RESULT IN PERMANENT DAMAGE TO THE ECU.
6. Do not allow the PC running J2534 Calibration Update Wizard software to go into standby or hibernation modes during the reprogramming process; FAILURE TO FOLLOW THIS INSTRUCTION WILL RESULT IN PERMANENT
DAMAGE TO THE ECU.
7. Do not cycle the ignition switch off during the reprogramming process except where instructed to do so by the Calibration Update Wizard or scantool software.
8. For ECUs that have more than one CPU to be reprogrammed, you must COMPLETE ALL CPUs before returning the vehicle to service.
9. To ensure stable battery voltage during this process, it is acceptable to connect a battery charger to the vehicle prior to beginning the reprogramming operation. Charger must be set on "low" charge rate and voltage must be maintained within the 11.4 volt to 16.0 volt window for the entire reprogramming process.
10. Set the parking brake for this operation

In addition to the above mentioned precautions, it is important to READ THE SPECIFIC TSB ASSOCIATED WITH THE REPROGRAMMING EVENT YOU ARE PERFORMING. Certain vehicles require removal of fuses to prevent accessories from energizing during the reprogramming process. FAILURE TO FOLLOW THE SPECIFIC DIRECTIONS IN THE APPLICABLE TSB FOR VEHICLE YOU ARE REPROGRAMMING CAN RESULT IN PERMANENT DAMAGE TO THE ECU.

View Getting-Started


Language: English
Quantity of CD: 1DVD
Date: 12.2009

スマホでQRコードをスキャンして、いつでも何処でも注文できる!
 
お問い合わせ
何か質問があれば、 お気軽にお知らせください。
Live Support:
オンラインチャット
E-Mail:sales@jobdii.jp
Skype:jobdii.jp

ご注意ください:
製品を安全に送るために、電話番号が必要です。ご注文する時、電話番号を教えてください。
また、製品が無事に保証するため、パッケージに署名する前に、損傷があるかどうかを二重にチェックしてください。
もし、商品は損傷があれば、損傷を受けた証拠を開いてください。
Attention: please leave your telephone number for shipping arrival when you make payment for this product on our website.
私たちのコミュニティに参加する:
ニュースレターはクーポンを得る:
 
 
 
 
Solution Graphics Singapore Post UPS TNT EMS DHL