製品説明
GODIAG GT100+ with Current Display New Generation OBDII Protocol Detector OBD2 Break Out Box ECU Connector. Including All the functions of GODIAG GT100. Add Current Display for ECU Module. Support more protocols like CANBUS, K-Line, PWM, VPW+, KWP2000. Support All Key Lost for Porsche, VW, Mitsubishi, etc.
GODIAG GT100 + with Current Display New Generation OBDII Protocol Detector OBD2 Break Out Box ECU Connector
Highlights to get GODIAG GT100 II:
1. Including all the functions of GODIAG GT100.
2. Add Current Display functions on the Main Unit. You can intuitively see the current display of the ECU by Connecting the ECU module with the Banana interface or the DB25 cable, which can make your work much easier.
3. GODIAG GT100+ can support more protocols like CANBUS, K-Line, PWM, VPW+, KWP2000.
4. Can support all key lost, activate the meter, and wake up the anti-theft module.
(1). For Porsche, VW 4th generation smart key &5th generation card key (models such as new A6L Touareg A4 Q5 A7), use GT100 short the banana PIN 16----PIN 1, After the instrument is on, the key matching tool connects to GT100+ female Head for data collection. Some vehicle instruments are not bright, but data can also be collected, for example, A6L Q7.
(2). Can replace the engine ECU for Toyota, and Support connect short-circuit PIN13-PIN4 with Key Programmer when doing all key lost for Toyota.
(3). Mitsubishi all key lost matching or all key lost for remote control key, need to set OBDII short-circuit PIN1-PIN4.
GT100 ECU connector Display:
GODIAG GT100 function and operation guide:
By connecting the vehicle and diagnostic tool via OBDII, Godiag GT100's LED will indicate whether the OBDII diagnostic interface has good communication with the car
Monitor the voltage of the vehicle OBDII interface and display it in real-time. If it is less than 11V, please stop the diagnosis and programming to avoid the vehicle being unable to start/data loss/module locked.
Indicator Meaning:
1. Manufacturer custom
2. SJE1850 wire
3. Manufacturer custom
4. Power grounding
5. Signal grounding
6. SAEJ2284《CAN》high
7. ISO9141-2&iso, DIS4230-4K wire
8. Manufacturer custom |
9. Manufacturer custom
10. SJE1850 wire《bus->
11. Manufacturer custom
12. Manufacturer custom
13. Manufacturer custom
14. SAEJ2284《CAN》low
15. ISO9141-2 & ISO/DIS 4230-4L wire
16. Car battery positive |
GODIAG GT100 Main Functions:
1. OBDII Protocol Detector & communication detection
1). Connect GODIAG GT100 to the OBDII diagnostic port of the car.
2). When the device displays the voltage, turn on the power switch of GODIAG GT100.
3). Then connect to the diagnostic tool, when the tool is communicating with the car, the LED indicator of the corresponding protocol will light up or flash. ( If the CAN protocol is detected, it will have the maximum brightness. When the communication is successful, the corresponding CAN-H and CAN-L will dim or twinkling weakly)
2. ECU connection: single module connection
GODIAG GT100, connected to a single ECU module, is convenient for a user to do the single-module diagnosis and programming.
1). Connect the ECU with the color jumpers. (If the ECU is CAN protocol, please check whether you will need to connect a 120-ohm resistor.)
2). The GODIAG GT100 can be powered by connecting to the OBDII diagnostic interface of the car, or by an AC power adapter.
3). To diagnose and program for a single ECU by connecting the diagnostic tool or ECU programmer.
3. Banana plug extension connection
Extend the car's OBDII 16pin interface to tell you whether the OBDII interface connection is good or not, which is convenient for the test of the OBDII interface voltage waveform.
4. Convert the OBD1 diagnostic interface to the standard OBD2
Use the connector to convert the OBD1 interface into the obd2 interface according to the diagnostic interface communication protocol.
5. Connect multiple ECU control modules at the same time, which is convenient for professional engineers to detect and maintain.
6. When to use the extension cables: The space of the diagnostic interface location is too narrow to connect to the diagnostic tool, or the user finds that the diagnostic cable is not long enough during maintenance. It can be extended by 1.2 meters.
7. Able to power the car when replacing the used battery.
1). Prepare battery A to supply power by connecting to No. 16 / 4 / 5 holes of Godiag GT100 & to the OBD2 diagnostic interface of the car.
[Notice 1. Turn on the power switch of Godiag GT100. 2. Don't turn on the ignition switch, don't start the car]
2). Then replace the brand-new battery B with the used battery in the car, which will ensure that the car has full power to prevent data loss and audio lock-up or malfunction due to lack of power to the ECU control module.
8. The dedicated adapter will be released (help GT100 connect to the special ECU module)
Hardware Connection Diagram:
GODIAG GT100 Parameter
Item |
Specification |
Diagnostic port |
OBDII |
Working voltage |
DC 9V-24V |
Work and power |
0.5-0.6W |
Adapter power |
Input AC100v-240v, Output DC12V 1A |
Operating temperature range |
-20 to 70 °C ( -4 to 158 °F ) |
Storage temperature range |
-40 to 85 °C ( -40 to 185 °F ) |
Dimension |
L: 23cm, W:18cm, H:7cm |
Package includes:
1pc x Host
1pc xOBD 2-in-1 extension cable
1pc xColored jumper cable
1pc xPower supply 12V
1pc xResistance 120 ohm
6pcs xBanana plug
24pcs xWire accessories, Dupont 2.54mm connector female pin
お問い合わせ何か質問があれば、 お気軽にお知らせください。
Live Support:オンラインチャット
E-Mail:
sales@jobdii.jpSkype:
jobdii.jpご注意ください:製品を安全に送るために、電話番号が必要です。ご注文する時、電話番号を教えてください。
また、製品が無事に保証するため、パッケージに署名する前に、損傷があるかどうかを二重にチェックしてください。
もし、商品は損傷があれば、損傷を受けた証拠を開いてください。
Attention: please leave your telephone number for shipping arrival when you make payment for this product on our website.